FINSQUIRT.FI

hi all! i made some modifies at the pcb:

- add jumper for the bootloader mode
- change the L7805 with the LM2937ET-5.0
- change clock capacitor

now i'm looking for another modify for save the CPU from the overtension from 5 volt of the sensors with a zener 5.6 volt between pin 31 and pin 32 of the ...

another question: at right of Motorola's socket there are 3 holes, near oscillator, in corresponding of pin 10 and pin 11. what are these?

i downloaded "virtual box" by Oracle and when i'll go home i'll install win98 to try this.

I've finisched the Turtana, with MPX4250GP, AD595AQ and i bought the Motorola MC908GP32CPE but i don't know how put the firmware MS Extra in the Motorola chip. I made the Willette Megaprogrammer but the software by P&E Microcomputer System "prog08sz" say me "Apro exception" error. I use win7.

there ...

Masi_K wrote:

ricki158 wrote:Because at the local shop i can order only mpx4250 and ad595aq, togheter 50 €

Whoa! Are those gold plated or what

ahahah!! really!

Because at the local shop i can order only mpx4250 and ad595aq, togheter 50 € and i want try to spend less. the motorola i can't order at local shop and i don't find it on ebay. i know that you must insert a firmware in the motorola before the installation of it in the megasquirt, and i also know ...

perfect! thanks!

finally someone has
1x motorola mc68hc908gp32
1x ad595aq
1x mpx4250gp

to sell me? how much?

thanks another time!

nothing?

the output for spark a is the "led 17" and the output for spark b is "led 19"?

any news?

ok, well, with bosch bip373 emettitor is ground, base is linked with the turtana's output and 330ohm resistor, and collector is linked with the coil, is true?

then where are the two exits for sparks in turtana's pcb?

what is the igtb's module? from where could i pick up the signal?

Then, can i program the Motorola MS 1 cpu with the MSextra firmware?

i prefer it too!
where could i found any schematic or something in english?

i found this for Ford EDIS module http://www.msextra.com/doc/ms1extra/MS_ ... l.htm#edis

But i'll use only the coil pack

thanks Just don't you know what is the fault?

i'll use this ecu with a Motorcraft Coil 928F-12029-CA 0277A (that is the coil of Ford EDIS module, but only the coil, not all module) and with a single point injector form Lancia Dedra 1.6. Then I'll have to make other changes?

there is d7 and the jumper is soldered on copper side?

then remove r40, 1,2,3,4 are not conneted and what else? i didn't understand about r47 and r44.

any news?
i made the megaprogrammer and the stimulator

i don't understand anything. can you help me with an image?

use these one

http://img818.imageshack.us/img818/2417/img20120426173818.jpg

http://img10.imageshack.us/img10/471/img20120426173827.jpg

http://img717.imageshack.us/img717/2992/img20120427005721.jpg

http://img812.imageshack.us ...

ahahah i love you!
what does it mean "shift light jump"?

i use a vr sensor, howis the bridge?

ok but i did't understand how many Farad for c46

and what is the function of these holes (circled in white)

ok but d9 and d10 36v or 24v?

and between c30 and the fuse socket there is c46 (what value?) and d8 22v zener?

ok, another question: L1 is 100 uH or 100 mH?
and what do i choose to c22, c23, c28, c29, d9 and d10?

what is the type of the capacitor c36? what are the charateristics of x1?

Hi everybody, I'm Riccardo from Italy.
I'm trying to make the Turtana, now i'm at 90%, but i haven't any electric scheme and some holes are available.
I tryed to contact the author but he didn't answer me.
I hope someone help me!

Riccardo

http://img11.imageshack.us/img11/1043/img20120409125741 ...